Skip Navigation

MODULES / UNITS

Product image

4 UP HORIZONTAL ADJUSTABLE DIE UNIT

The unit will accept up to three more rollers (four including the bottom anvil). These rollers can be dies, steel anvils, rubber rollers or any combination depending on the application.

The unit can be rapidly adjusted in the direction of the web by a lever while the machine is operating.

This unit is available in sizes:

175 only.

Pleas... More Details

Product image

HORIZONTAL ADJUSTABLE DIE UNIT

This unuit will accept a single tool up to 12'' (304.8mm) repeat. The unit can be rapidly adjusted in the direction of the web by a lever while the machine is running.

This unit is available in sizes:

175 only.

Please contact Ident Machines Ltd. for more information.... More Details

Product image

HORIZONTAL ADJUSTABLE DIE UNIT for FINE ADJUSTMENT

This unuit will accept a single tool up to 12'' (304.8mm) repeat. The unit can be rapidly adjusted in the direction of the web by a lever while the machine is running.

This unit is available in sizes:

110 and 175.

Please contact Ident Machines Ltd. for more information.... More Details

Product image

SILICONE APPLICATOR

The silicone applicator cane be attached to any standard die unit to allow lubrication of the cutting tool.

This unit is available in sizes:

110, 175, 250, 280, 320, 350, 400, 480.

Please contact Ident Machines Ltd. for more details.... More Details

Product image

STACKER

The unit is used for stacking sheeted parts. The stacked pile is created by feeding the sheets under each other to produce a stack. The unit is normally fitted directly at the sheeting die.

This unit is available in sizes:

110, 175, 250, 280, 320, 350, 400, 480, 550.

Please contact Ident Machines Ltd. for more details.... More Details

Product image

SHINGLE STACKER

The stacker is fitted to the rewind end of the press, there are no mechanical fixings required. The unit is totally self-contained.
This unit is available in sizes:

175, 250, 280, 320, 350, 400, 480, 550.... More Details

Product image

200mm WIDE DIE UNIT

This die unit will accept tool up to 25'' (625mm) repeat. Pressure is applied to the tool by the two adjusting screws on top of the unit.

The unit can be adjusted across the web while the machine is operating.

This unit is available in sizes:

110 and 175.

Please contact Ident Machines Ltd. for more details.... More Details

Product image

CONVERSION DIE UNIT

This unit will allow any standard 175 tool to be run on a larger machine. The conversion die unit will accept a single tool up to 18'' (457mm) repeat and can be adjusted across the web while the machine is operating.

This unit is available in sizes:

250, 280, 320, 350, 400, 480, 550.

Please contact Ident Machines Ltd. for more details.... More Details

Product image

5 UP BACK-CUTTING DIE UNIT

The 5 up back cutting die allows dies, anvils or laminating rollers to be placed in any position in the unit, thus making it possible to cut on both sides of the web simultaneously by ā€œSā€ wrapping through the unit.

All five rollers can be removed.

This unit is available in sizes:

175 only.

Please contact Ident Machines Ltd. for more... More Details

Product image

REVERSIBLE SKELETON REWIND WITH SPLIT CORES

The skeleton rewind has an incorporated gearbox, so the direction of the wind can be changed. Split cores (up to five-way) are available for this unit. Standard friction clutches are used for tension control.

This unit is available in sizes:

110, 175, 250, 280, 320, 350, 400, 480, 550.

Please contact Ident Machines Ltd. for more informatio... More Details

Results Pages: << Previous Products | 1 | 2 | 3 | 4 | More Products >>